Leading 10 common forklift accidents ， forklift operation should pay attention to these issues ！.

Don't underestimate the forklift at work. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be risk-free before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no challenges overhead. When the load is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed doglegs will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load will not be elevated other than when piling or packing. .
8. The height of the tons should not block the driver's sight. In unique conditions, when the thing impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold items and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the range in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the shelf. .
2. It is prohibited to collaborate with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the lots, and it ought to be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to avoid the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork framework.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for special situations, such as the driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security Stand-on Electric Pallet Stacker efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, examine whether the stress and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary Stand-on Electric Pallet Stacker fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844